home automation

56 blocks in 1 groups. Open a block for its pins, an example and how it behaves.

home

• get device history array v15.0.0 Returns recorded readings for one capability of one device, optionally bucketed for charting.
• climate set condition v15.0.0 Sets an air conditioner or thermostat: on/off, mode, target temperature, fan speed.
• get all devices array v15.0.0 Returns every adopted device, optionally filtered by type, room or adapter.
• contact opened object v15.0.0 Starts the flow when a door or window is opened.
• door or gate opened object v15.0.0 Starts the flow when a controlled door or gate physically opens.
• light off condition v15.0.0 Turns a light off.
• switch turned off object v15.0.0 Starts the flow when a plug, relay or switch is turned off.
• pairing open condition v15.0.0 Opens the radio for new devices to join, for a bounded number of seconds.
• temperature changed object v15.0.0 Starts the flow when a temperature reading changes. Set above or below to fire only when it crosses a threshold.
• device set condition v15.0.0 Sets any capability on any device. The escape hatch for things the specific blocks do not cover.
• door or gate closed object v15.0.0 Starts the flow when a controlled door or gate physically closes.
• light toggle condition v15.0.0 Flips a light: on if it is off, off if it is on.
• gate close condition v15.0.0 Closes a gate or garage door.
• presence cleared object v15.0.0 Starts the flow when a room becomes empty.
• door or gate unlocked object v15.0.0 Starts the flow when the lock releases, whether or not the door then opens.
• get device state condition v15.0.0 Reads one capability from one device — is the motion sensor triggered, what is the temperature.
• device adopted object v15.0.0 Starts the flow when a device is taken into service.
• water leak detected object v15.0.0 Starts the flow when a leak sensor finds water.
• device forget condition v15.0.0 Removes a device from RUAL. It stays paired to the radio and will reappear, unadopted, on its next report.
• switch turned on object v15.0.0 Starts the flow when a plug, relay or switch is turned on.
• light turned on object v15.0.0 Starts the flow when a light is switched on — by anyone, including a wall switch or the vendor's own app.
• switch on condition v15.0.0 Turns a plug, relay or switch on.
• get status array v15.0.0 Returns which radios are connected and how many devices are known.
• get device condition v15.0.0 Returns one device: its name, room, capabilities and current state.
• light dim condition v15.0.0 Sets a light's brightness without changing anything else.
• door or gate locked object v15.0.0 Starts the flow when the lock engages.
• device state changed object v15.0.0 Starts the flow on ANY change from a device. The catch-all — use a specific trigger where one exists.
• door unlock condition v15.0.0 Unlocks a door. By default this is a momentary unlock — the door releases long enough for one person, then re-locks — matching the 'let them in' button.
• humidity changed object v15.0.0 Starts the flow when a humidity reading changes. Set above or below to fire only when it crosses a threshold.
• device rename condition v15.0.0 Sets a device's friendly name and/or room.
• door lock condition v15.0.0 Locks a door, and holds it locked unless you ask it not to.
• access denied object v15.0.0 Starts the flow when someone is refused: an unknown card, a wrong PIN, a credential outside its schedule.
• device adopt condition v15.0.0 Takes a discovered device into service, so triggers fire for it and blocks can command it.
• camera motion detected object v15.0.0 Starts the flow when a camera detects motion.
• get lights that are on array v15.0.0 Returns every light currently switched on.
• get active sensors array v15.0.0 Returns every sensor that is currently triggered: motion present, doors open, leaks found.
• button pressed object v15.0.0 Starts the flow when a button or scene switch is pressed. The `value` pin says which press it was: single, double, hold, release.
• device discovered object v15.0.0 Starts the flow when a NEW device appears on the radio, before it is adopted.
• smoke detected object v15.0.0 Starts the flow when a smoke alarm triggers.
• light turned off object v15.0.0 Starts the flow when a light is switched off.
• presence detected object v15.0.0 Starts the flow when someone is detected in a room.
• gate opened object v15.0.0 Starts the flow when the gate physically opens.
• get rooms array v15.0.0 Returns the list of rooms that have devices assigned to them.
• doorbell rang object v15.0.0 Starts the flow when someone rings a doorbell or door station.
• gate open condition v15.0.0 Opens a gate or garage door.
• nfc card swiped object v15.0.0 Starts the flow when any NFC card or fob is presented to a reader, whether or not it was accepted.
• access granted object v15.0.0 Starts the flow when someone is let in: a valid card, PIN, wave or mobile credential. The actor and method are on the out-pins.
• sensor deactivated object v15.0.0 Starts the flow when a sensor turns OFF: motion cleared, a door closed, a leak stopped.
• switch off condition v15.0.0 Turns a plug, relay or switch off.
• sensor activated object v15.0.0 Starts the flow when a sensor turns ON: motion detected, a door opened, water found, smoke detected.
• battery low object v15.0.0 Starts the flow when a device's battery drops below the threshold, or reports its own low-battery flag.
• gate closed object v15.0.0 Starts the flow when the gate physically closes.
• light on condition v15.0.0 Turns a light on. Optionally set brightness, colour temperature or colour in the same command.
• security alarm activated object v15.0.0 Starts the flow when the security system's own alarm goes active.
• device unavailable object v15.0.0 Starts the flow when a device stops responding.
• contact closed object v15.0.0 Starts the flow when a door or window is closed.